RIDGID MS1250LZA Manual de Serviço

TECHNICAL DATAANDSERVICE MANUALCOMPOUND MITER SAWC 12LCHC 12LCC 12FCHSPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENTLIST No

--- 6 ---305 (12")154,000Not providedDouble insulationNone585 x 635 x 600(23-1/32" x 25" x 23-5/8")19.3 (43 lbs.)305 (12")153

--- 7 ---7. PRECAUTIONS IN SALES PROMOTIONIn the interest of promoting the safest and most efficient use of the Models C 12LCH, C 12LC and C 12FCHCo

--- 8 ---(2) Warning label (A)Fig. 3Fig. 4Warning label (A) specified by the UL is affixed on the right side of the base. Please instruct users to st

--- 9 ---Fig. 6-2(5) Warning label (C) (at the front of sub fence)Fig. 7(6) Caution label (F) (at the front of link (B)) (for Europe)Fig. 8Caution l

--- 10 ---7-3. Relative StandardsStandards, regulations and guidelines for the safe use of laser equipment.[The U. S. A.]There is a standard "C

--- 11 ---7-5. Ambient Illuminance and Visibility of Laser Line (Models C 12LCH/C 12FCH)The visibility of the laser line on the workpiece changes de

--- 12 ---The laser line is adjusted to the width of the saw blade at the timeof factory shipment. Depending upon the cutting choice, align thelase

--- 13 ---CAUTION:Laser radiation - Do not stare into beam.Laser radiation on work table. Do not stare into beam. If your eye is exposed directly

--- 14 ---8-3. Confirmation for Use of Sub FenceThis power tool is equipped with a sub fence.In the case of direct angle cutting and angle cutting,

--- 15 ---8-4. Cutting Operation(1) Cutting efficiency will be reduced if a dull saw blade is used, if an excessively long extension cord is used, o

REMARK:Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol(s)is(are) used in the place of company name(s) and model name(s)

--- 16 ---(7) Bevel angle fine adjustmentGrip the handle on the motor head and position it at the bevel angle you need. Temporarily tighten the cla

--- 17 ---(9) Crown molding cuttingThis machine can cut two types of crown molding workpieces by combining the miter and bevel cuttingoperations (f

--- 18 ---(1) Setting to cut crown molding at positions and in Fig. 17 (See Fig. 18, tilt the head to the left.):Turn the turn table to th

--- 19 ---Cutting method of crown molding without tilting the saw blade6 mm wing boltCrown molding stopper (L)(Optional accessory)Crown moldingstopp

--- 20 ---8-5. Digital Display Panel (Models C 12LCH/C 12LC)(1) Turning on the digital display switch shows 0û for both miter and bevel angle, regar

--- 21 --- CAUTION:If the figure shown on the miter angle digital display is different from the positive stop angle (for example,45.0û 45.5û

--- 22 ---9. ADJUSTMENT OF COMPONENTS9-1. Bevel Angle AdjustmentBefore the power tool is shipped from the factory, it is adjusted for 0û, left 45û b

--- 23 ---Base packingPacking (C)Packing (E)Fig. 29Fig. 28Carton boxUpper packingPacking (B)Packing (A)Fig. 30

--- 24 ---11. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLY11-1. Precautions in Disassembly and Reassembly of the Laser Marker (Models C 12LCH/C 12FCH)D

--- 25 ---1. Remove the Machine Screw (W/Washers) M4 x 10 (Black) [68] and Indicator (B) [67]. Remove the twoMachine Screws (W/Washers) M5 x 16 [4

PageCONTENTS1. PRODUCT NAME ...

--- 26 ---7. Remove the Machine Screw (W/Washers) M4 x 16 [31] and the Nylon Clip [32]. Then remove the fourMachine Screws M4 x 10 [38] to remove

--- 27 ---B. Armature ass'yCord, stator ass'y and housing ass'yTools required: • Phillips screwdriver • Flat-blade screwdriver • Plas

--- 28 ---1. Remove the two Tapping Screws (W/Flange) D4 x 25 (Black) [237] and the four Tapping Screws (W/Flange)D4 x 20 (Black) [246], then remov

--- 29 ---C. Safety cover and linkSpindle and springTools required: • Phillips screwdriver • Hex. bar wrench 5 mm • Hex. bar wrench 4 mm • Hex. bar

--- 30 ---1. Remove the Machine Screw M5 x 10 (Black) [234] at the notched side of the Spindle Cover [236] and slide theSpindle Cover [236] to remo

--- 31 ---1. Remove the two Tapping Screws (W/Flange) D4 x 25 (Black) [237] and the four Tapping Screws (W/Flange)D4 x 20 (Black) [246], then remov

--- 32 ---F. Digital display (Models C 12LCH/C 12LC)Tool required: • Phillips screwdriverFig. 371. Remove the Indication Panel Ass'y [128] and

--- 33 ---11-3. ReassemblyReassembly can be accomplished by following the disassembly procedures in reverse. However, specialattention should be gi

--- 34 ---11-4. Wiring DiagramCarefully ensure that wiring is accomplished as illustrated below. As incorrect wiring will result in lack of rotatio

--- 35 ---Wiring diagram (C 12LCH)Fig. 38-2

Page11-9. Adjustment of Laser Marker Accuracy (Models C 12LCH/C 12FCH) ...4311-10. Tightening Torque...

--- 36 ---C 12LCH Europe/AUS/NZL/ChinaFig. 39-1Fig. 39-2

--- 37 ---Fig. 40-2Wiring diagram (C 12LC) USA/CANFig. 40-1

--- 38 ---C 12LC Europe/NZLFig. 41-1Fig. 41-2

--- 39 ---Fig. 42-2Wiring diagram (C 12FCH) USA/CANFig. 42-1

--- 40 ---C 12FCH Europe/NZL/AsiaFig. 43-1Fig. 43-2

--- 41 ---11-5. No-load CurrentAfter no-load operation for 30 minutes, the no-load current values should be as follows.11-6. Reassembly Requiring Ad

--- 42 ---Tolerance0.2/280 (0.008"/11")0.2/height of fence (0.008"/height of fence)0.2 (0.008")0.2/100 (0.008"/4")0.2/

--- 43 ---11-9. Adjustment of Laser Marker Accuracy (Models C 12LCH/C 12FCH)(1) Construction of laser marker and functions of each componentFig. 47

--- 44 ---(2) Adjustment of squareness with the fence surfaceThe laser line inclines to the left by turning the Hex.Socket Set Screw M5 x 6 [6] cloc

--- 45 ---(4) Adjustment of the laser markerAdjust the laser marker according to the following steps from to .Adjust the product accuracy

--- 1 ---1. PRODUCT NAMEHitachi Compound Miter Saw, Models C 12LCH, C 12LC and C 12FCH2. MARKETING OBJECTIVEFollowing the 10" compound miter sa

--- 46 ---11-10. Tightening Torque(1) Model: C 12LCH• Machine Screw (W/Washers) M6 x 20 (Black) [16] 43.4 in-lbs. (4.9 N•m, 50 kgf•cm)• Machine Scre

--- 47 --- a Inaccuratesquareness betweenthe turn table and thesaw blade causes thesaw blade to cut intothe workpiece at anangle. b Excessive defl

--- 48 ---• Same as the Item 1- b .• Replace Washers (A) [194] and(B) [192].• Same as the Item 1- a .• Same as the Item 1- e .• Correct warp o

--- 49 ---a The power cord is notconnected to powersupply.b The carbon brushwear exceedsallowable limit (5 mm).c Contact failure of themicro swit

--- 50 ---a Ink line is not rightangle.b Laser marker accuracyis not adjustedproperly.c Product accuracy isnot good.------0.2/100(Figs. 59 and 60

--- 51 ---ItemPhenomenonCauseFactorystandardInspection, repair oradjustmenta Same as item 10- a to f .b Encoder failurec Cord (A) is dis

--- 52 ---13. STANDARD REPAIR TIME (UNIT) SCHEDULESMODEL 10 20 30 406070 min.50FixedVariableC 12LCHWork FlowSwitch Handle(C)LinkProtectiveCover (B)P

ELECTRIC TOOL PARTS LISTLIST NO. E938COMPOUND SAWModel C 12LCH2005 • 6 •30(E2) Hitachi Power Tools725164676674A12A61011394041434546474849505253

--- 2 --- 6 -- 05C 12LCH622623624625626627628621101102103104105106107110108108111112114115116117118119120121123 124125126127128129130131132133130134

--- 3 ---6 -- 05C 12LCH19823623322526621621321423123223021821922022122219219119319619419519720020120220320420520620921021120920822923524525424624824

--- 2 ---(2) Laser guide system (Only Models C 12LCH and C 12FCH)Use the laser marker for aligning with the ink line on the workpiece.Cutting position

* ALTERNATIVE PARTS--- 4 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12LCH1 323-141 SPRING (B) 12 323-137 LASER HOLDER (A) 13 323-138

* ALTERNATIVE PARTS --- 5 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS6 -- 05C 12LCH52 949-821 HEX. SOCKET HD. BOLT M5X16 (10 PCS.) 153 323-664

* ALTERNATIVE PARTS--- 6 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12LCH124 990-541 MACHINE SCREW (W/WASHERS) M5X16 4125 323-612 MON

* ALTERNATIVE PARTS --- 7 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS6 -- 05C 12LCH173 323-610 MONITOR ASS’Y 1 INCLUD. 125, 130-133191 988-101

* ALTERNATIVE PARTS--- 8 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12LCH* 241 500-234Z CORD 1 (CORD ARMOR D10.7)* 241 500-435Z CORD

* ALTERNATIVE PARTS --- 9 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS6 -- 05C 12LCH275 322-123MACHINE SCREW (W/WASHERS) M5X40 (BLACK)4* 276 324

* ALTERNATIVE PARTS--- 1 0 --- 6 -- 05OPTIONAL ACCESSORIESITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDSTANDARD ACCESSORIESITEMNO.CODE NO.DESCRIPTIONRE

ELECTRIC TOOL PARTS LISTLIST NO. E940COMPOUND SAWModel C 12LC2005 • 6 •30(E2) Hitachi Power Tools725164676630A74A394041434546474849505253545662

--- 2 --- 6 -- 05C 12LC62262362462562662762862110110210310410510610811111211411511611711811912012112312412512612712812913013113213313013413513613713

--- 3 ---6 -- 05C 12LC198236233225266276281277278279280293286213285292287288289290291213216216213 216285 2922842822832942952962162132142312322302182

--- 3 ---(7) Powerful 15 amps motor (for the U.S.A. and Canada)The Models C 12LCH, C 12LC and C 12FCH are equipped with a 15-ampere motor. The Mode

* ALTERNATIVE PARTS--- 4 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12LC16 323-208MACHINE SCREW (W/WASHERS) M6X20 (BLACK)117 322-935

* ALTERNATIVE PARTS --- 5 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS6 -- 05C 12LC68 304-043MACHINE SCREW (W/WASHERS) M4X10 (BLACK)169 680-418

* ALTERNATIVE PARTS--- 6 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12LC141 949-216 MACHINE SCREW M4X10 (10 PCS.) 1142 322-954 VISE S

* ALTERNATIVE PARTS --- 7 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS6 -- 05C 12LC209 993-539 MACHINE SCREW (W/WASHERS) M4X16 2210 323-689 GEAR

* ALTERNATIVE PARTS--- 8 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12LC* 258 323-633 INTERNAL WIRE (A) 1 FOR USA, CAN259 322-914 HOU

* ALTERNATIVE PARTS --- 9 ---6 -- 05STANDARD ACCESSORIESOPTIONAL ACCESSORIESITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDITEMNO.CODE NO.DESCRIPTIONREMAR

--- 1 0 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USED6 -- 05C 12LCPrinted in Japan(050630N)

ELECTRIC TOOL PARTS LISTLIST NO. E939COMPOUND SAWModel C 12FCH2005 • 6 •30(E2) Hitachi Power Tools5164676630A74A12A6101139404143454647484950525

--- 2 --- 6 -- 05C 12FCH622623624625626627628621104105106107118119120121123124126132135136137138139140141142143144146145147148149150151152153154159A

--- 3 ---6 -- 05C 12FCH198236233225266282283501502503276281277278279280293286213285292287288289290291213216216213 216285 292284294295296216213214231

--- 4 ---5. SPECIFICATIONS63.5 mm (2-1/2") x 200 mm (7-7/8")98 mm (3-7/8") x 155 mm (6-1/8")MaximumcuttingdimensionsHeight xWidth(

* ALTERNATIVE PARTS--- 4 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12FCH1 323-141 SPRING (B) 12 323-137 LASER HOLDER (A) 13 323-138

* ALTERNATIVE PARTS --- 5 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS6 -- 05C 12FCH60 303-006 SPACER D4X10 261 949-432 BOLT WASHER M6 (10 PCS.)

* ALTERNATIVE PARTS--- 6 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12FCH160 949-610 BOLT M6X10 (10 PCS.) 1161 987-512MACHINE SCREW (

* ALTERNATIVE PARTS --- 7 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS6 -- 05C 12FCH229 322-926 LASER COVER (A) 1230 322-947 SPECIAL SCREW (C) M

* ALTERNATIVE PARTS--- 8 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS6 -- 05C 12FCH268 323-637 LOCK LEVER 1269 302-428 WASHER (A) 1270 600-0VV

* ALTERNATIVE PARTS --- 9 ---6 -- 05STANDARD ACCESSORIESOPTIONAL ACCESSORIESITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDITEMNO.CODE NO.DESCRIPTIONREMAR

--- 1 0 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USED6 -- 05C 12FCHPrinted in Japan(050630N)

--- 5 ---305 mm (12") TCT saw blade (60 teeth, Code No. 305546)Extension holder and stopperCrown molding vise ass'y (including crown moldi