RIDGID MaxSelect R885 Manual do Operador

1Your circular saw has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly

10FEATURESASSEMBLYKNOW YOUR CIRCULAR SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in this

1150505050ATTACHING THE BLADESee Figure 2.WARNING: A 6-1/2 in. blade is the maximum blade capacity of the saw. Never use a blade that is too

12WARNING:Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict sev

13OPERATIONTO CHARGE A fully discharged battery pack with a temperature between 32°F (0°C) and 150°F (65°C) will charge in about an hour. Charge the

14LED FUNCTION OF RIDGID 24V LITHIUM-ION CHARGERSee Figure 6.OPERATIONLEDINDICATORBATTERY PACKREDLEDGREENLEDACTIONCharging Fast charging ON OFF Charge

15LED FUNCTION OF RIDGID NICKEL-CADMIUM CHARGERSSee Figure 7.Fig. 7POWER INDICATOREVALUATE INDICATORCHARGING INDICATORFULL INDICATORLEDINDICATORBATTER

1624vXLi?TO INSTALL BATTERY PACKSee Figure 8. Place the battery pack in the saw. Align the raised rib inside the saw with the groove on the

17OPERATIONFig. 10Fig. 11KICKBACKSee Figures 10 - 13.Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stall

18INDICATOR POINTLOCK-OFF BUTTONSee Figure 14The lock-off button reduces the possibility of accidental starting. The lock-off button is located

195050OPERATIONOPERATING THE SAWSee Figures 17 - 18.It is important to understand the correct method for oper-ating the saw. Refer to the figures in t

2 Introduction ...

2050500876545050OPERATIONFig. 19CROSS CUTTING/RIP CUTTINGSee Figures 19 - 20.When making a cross cut or rip cut, align your line of cut with the outer

21505050505050OPERATIONFig. 22BASE ASSEMBLYWIDTH OF CUT SCALEBEVEL ADJUSTMENT LEVERBEVEL CUTTINGSee Figures 23 - 24.The angle of cut of the saw may b

22505050500° BEVEL STOPSee Figure 25.The saw has a 0° bevel stop that has been factory adjusted to assure 0° angle of the saw blade when making 90° cu

23MAINTENANCEWARNING:When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause produ

24Look for these accessories where you purchased this product:�� Edge Guide*...Part no. 631697001WARNING:Cur

25WARRANTYProof of purchase must be presented when requesting war-ranty service. Limited to RIDGID® hand held and stationary power tools purchased 2/1

26983000-96904-19-07 (REV:02)Customer Service Information:For parts or service, contact your nearest RIDGID authorized service center. Be sure to prov

3GENERAL SAFETY RULESWARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire an

4GENERAL SAFETY RULESSPECIFIC SAFETY RULES Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manne

5SPECIFIC SAFETY RULESADDITIONAL SAFETY RULES Check damaged parts. Before further use of the tool, a guard or other part that is damage

6SAFETY RULES FOR CHARGERWARNING!READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock,

7SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will

8SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su

95050FEATURESFig. 1PRODUCT SPECIFICATIONSBlade Diameter ..............6-1/2 in.Blade Arbor ......