RIDGID R4511 Manual do Operador descarregar pdf (Página 18)

ASSEMBLY

ASSEMBLY

•

Repeat

above

step

for

the

upper

section

of

the

Herc-U

Lift®.

•

Check

to

insure

the

upper

and

lower

sections

are

centered.

If

required,

loosen

frame

hardware

and

adjust

the

frames

side

to

side

to

center.

Retighten

all

hardware.

•

Press

down

on

the

unlock

pedal

to

check

alignment

of

the

U-bolt.

The

U-bolt

should

be

centered

within

the

latch

mechanism

as

shown

in

figure

17.

Release

the

unlock

pedal

and

adjust

the

U-bolt

as

necessary.

Retighten

all

hardware.

NOTE:

With

the

tool

on

a

level

surface,

check

to

make

sure

the

tool

does

not

move.

If

tool

moves,

adjust

all

four

leveling

feet

supporting

the

tool.

A

WARNING:

Only

install

the

dust

chute

when

using

a

four

inch

dust

collection

system.

Failure

to

heed

this

warning

could

result

in

serious

personal

injury

or

death.

Clean

saw

dust

from

the

cabinet

regularly.

TO

INSTALL

THE

DUST

CHUTE

See

Figure

18.

•

Place

the

dust

chute

inside

the

leg

stand

as

shown

in

figure

18.

NOTE:

Place

the

front

of

the

dust

chute

on

the

front

of

the

leg

stand

(note

“front”

label).

TO

MOUNT

THE

TABLE

SAW

TO

THE

LEG

STAND

See

Figure

18.

Step

down

on

the

pedal

to

lock

the

leg

stand

in

place.

•

With

the

aid

of

another

person,

place

the

table

saw

cabinet

on

the

leg

stand.

NOTE:

Place

the

front

of

the

saw

cabinet

on

the

front

of

the

leg

stand

(note

“front”

label).

•

Open

the

motor

cover

by

loosening

the

screws.

•

Align

the

holes

in

the

cabinet

with

the

holes

in

the

leg

stand.

•

Insert

a

screw

through

the

hole

in

the

cabinet

and

the

hole

in

the

leg

stand.

Hand

tighten.

•

Repeat

for

remaining

holes.

Tighten

all

hardware

securely.

•

Secure

the

dust

chute

to

the

saw

cabinet

using

hex

head

bolts.

•

Tighten

all

the

hardware

on

the

leg

stand

with

a

wrench.

•

Close

the

motor

cover

and

secure

in

place

using

screws.

LEG

LEVELING

FOOT

LOWER

SECTION

Fig.

13

TO

ASSEMBLE

THE

LEVELING

FEET

See

Figure

13.

Thread

a

hex

nut

on

each

of

the

leveling

feet

and

screw

it

down

towards

the

foot.

•

Put

the

leveling

feet

through

the

holes

in

the

bottom

of

each

leg.

Hand

tighten

until

they

are

next

to

the

bottom

support

of

the

leg.

NOTE:

Once

the

saw

is

in

its

permanent

location

the

leveling

feet

may

need

to

be

adjusted.

TO

ADJUST

THE

LEVEUNG

FEET

Move

the

table

saw

to

the

location

where

it

will

reside

dur

ing

use.

To

level

the

cabinet,

loosen

the

nut

and

adjust

leveling

feet

up

or

down

as

needed.

Adjust

all

four

leveling

feet

if

neces

sary

and

then

retighten

the

nut.

NOTE:

These

levelers

are

not

intended

for

height

adjustment,

only

leveling

adjustment.

TO

INSTALL

THE

HERC-U-UFT®

MOBILE

BASE

TO

THE

LEG

STAND

See

Figures

14

-

17.

To

assemble

the

lower

section:

Thread

flange

nuts

onto

the

U-bolt

as

far

as

they

will

go.

•

Slide

the

U-bolt

into

the

center

holes

on

the

U-bolt

tube

and

secure

in

place

using

flange

hex

nuts.

•

Place

the

front

tube

on

top

of

the

U-bolt

tube.

Insert

screws

into

the

aligned

holes

on

both

the

tube

and

support.

Finger

tighten

using

lock

nuts.

NOTE:

The

small

holes

on

the

front

tube

must

be

facing

up.

•

Place

the

tube

support

under

the

front

tube

and

secure

in

place

with

the

screws

and

lock

nuts

from

blister

pack.

•

Repeat

for

other

side

of

the

lower

section.

•

Place

the

caster

up

through

the

hole

in

the

lower

section

and

secure

in

place

using

flanged

nuts.

Repeat

for

other

side.

To

assemble

the

upper

section:

Place

the

unlock

pedal

assembly

on

top

of

the

rear

tubes.

Secure

in

place

using

the

screws

and

lock

nuts.

•

Place

the

caster

up

through

the

hole

in

the

center

brace

then

through

the

rear

tube

and

secure

in

place

using

flanged

nuts.

Repeat

for

other

side.

To

assemble

the

Hero-U-Lift®

to

the

leg

stand:

•

Place

the

lower

section

under

the

leg

stand

with

the

ends

of

the

tube

under

the

front

leg

brackets.

Place

a

screw

with

washer

through

the

leg

bracket

and

the

end

of

the

tube

of

the

lower

section.

Secure

in

place

using

nylock

nuts.

NOTE:

The

screw

should

freely

pivot.

SCREW

(M6x50)

FRONT

TUBE

SMALL

HOLE

ON

TOP

UPPER

SECTION

Fig.

14

UNLOCK

PEDAL

ASSEMBLY

REAR

TUBE

FLANGED

NUT

(M12)

CENTER

SMALL

HOLE

ON

TOP

U-BOLT

CENTER

U-BOLT

WITHIN

THE

LATCH

MECHANISM

Fig.

17

ONLY

INSTALL

WHEN

USING

41n.

DUST

COLLECTION

SYSTEM

CASTER

(M6x35)

18

Fig.

15

19

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 47 48

Comentários a estes Manuais

Sem comentários