RIDGID metal detector Guia do Utilizador Página 101
- Página / 144
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Operating Instructions
The Reject Set Up menu options available are as follows:
■ Mode
The following Mode options are provided for selection:
o Pulse (only available if a photo-eye is fitted)
If this option is selected, when a contaminated package is detected the reject delay time
is counted down, in order for the package to travel from the photo-eye to the reject
device, where-upon the reject is turned on for a time equal to the reject dwell time.
Typically, this mode of reject would be used for air blast or pusher type rejects for the
accurate rejection of small packages at high speed.
o Pulse Extension
This option provides the same functionality as the Pulse option, except that the dwell
time is extended if a second contaminated product reaches the reject point before the
dwell time from the first contaminated product has timed out. This could typically be used
with an air blast or retracting band reject device, but not a pusher type device. This reject
mode is always available.
o Toggle (only available if a photo-eye is fitted)
If this option is selected, when a contaminated package is detected the reject delay time
is counted down, in order for the package to travel to the reject device, where upon the
reject device state is toggled.
The Reject dwell option will not be displayed for configuration in the Menus > Service >
Options menu as it is not used.
o Dwell Extension
If this option is selected, when a contaminated product is detected the reject device is
immediately activated, and stays activated for a time equal to the reject dwell time. If a
second reject product is detected before the dwell time has timed out, then the dwell time
is counted down from the beginning again.
The Reject delay option will not be displayed for configuration in the Menus > Service >
Options menu as it is not used.
o Reject till accept:
If this option is selected, when a contaminated product is detected the delay time is timed
out, at which point the reject device becomes activated. The reject device will then stay
activated until an uncontaminated product reaches the reject point.
The Reject dwell option will not be displayed for configuration in the Menus > Service >
Options menu as it is not used.
■
Reject Relay
The reject relay can be set to be either normally energised or normally de-energised. For fail
safe applications, the relay state should be normally energised so that if there is a fault in the
reject system the relay will drop out causing rejection of all product.
■
Reject Timing
Two reject timing options are available for selections as follows:
91
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Manuais e produtos relacionados com Medição, teste e controlo RIDGID metal detector
(5 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.616 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais