RIDGID metal detector Guia do Utilizador Página 91
- Página / 144
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Operating Instructions
■ Noise Filter
This feature provides options for automatically filtering out background noise which could
affect the identification of contaminants in products. Options of OFF, LOW and HIGH are
provided for selection.
■
Control Board
The control board type that is currently fitted to the detector head is displayed. This is not
editable.
■
RX TX Board
The RX TX board type that is currently fitted to the detector head is displayed. This is not
editable.
Setting Up the Service Options
To set up the service options, proceed as follows:
1.
Select Menus > Service > Options to display the Service Options menu options which are
listed and described below.
2.
Use the Navigation Keys
to select each option in turn press the OK /
Enter Key
to enable the value to be edited.
3.
Use the Navigation Keys
to select the required option value and then
press the OK / Enter Key
to confirm the selection.
4. Repeat step 2 and 3 until you have selected and confirmed values for each option.
The Service Options menu contains the following options:
■
Tracker
Enabling the Tracker functionality allows product threshold values to follow any changes in
measured product effect. This option is only available when a product registration photo-eye
is in use. See Enabling the Tracker Feature
for further details.
■ Reject time
Selecting this option enables the Reject delay and Reject dwell values to be updated.
Therefore, leaving this option disabled prevents accidental changes being made to the reject
timings.
■
Set Up Learn
Selecting this option enables the Menus > Learn > Set Up menu to be displayed for selection.
■
Access ferrite
Selecting this option allows access to the Ferrite (F) product option in the Menus > Change
menu.
As this product is setup in the factory and its settings used by the detector as the baseline for
inspecting Dry products, access should be disabled to avoid incorrect use.
Access is generally enabled by a Loma Service Engineer when the Ferrite product needs to
be re-learnt following replacement of a circuit board or upgrading of the detector software.
81
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Manuais e produtos relacionados com Medição, teste e controlo RIDGID metal detector
(5 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais