RIDGID metal detector Guia do Utilizador Página 103
- Página / 144
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Operating Instructions
3.
Use the Navigation Keys
to select an unused product number and then
press the OK / Enter Key
to confirm the selection.
4.
Repeat steps 2 and 3 to scroll through all of the Product menu options until you have
selected and confirmed values for each option.
The Product menu options available are as follows:
■ Product No (number)
Each product must have a unique product number which is used by the software to store the
product settings for recall when the product is selected to be run.
■ Name
To assist with identification and selection, you should give all products a unique name, which
can be up to 25 alphanumeric characters in length.
■ Product type
The available options for selection are described below.
O Unknown
This is the default option and is recommended for selection if you are in any doubt
whether the other options available are more appropriate. In effect you are letting the
detector decide which product type is most suitable to use.
If during the product Learn process no product effect is exhibited, the detector will
automatically select the Dry option anyway.
O Dry
Select this option if you are sure that the product will exhibit no product effect. The
detector will then use the pre-set ferrite phase angle rather than learn from the actual
product.
If during the product Learn process a product effect is exhibited, the detector will advise
that the Learn process has failed. You should then set the Product type to Unknown and
repeat the learn process.
O Metal film
Select this option if the product to be inspected is foil packed.
Note that this option will only appear if the Auto-Frequency option is selected and the
Dry Working Mode option is not selected in the Menus > Learn > Set Up menu.
■ Flow length
The Flow length option is displayed if a Product Registration Photo-eye is in use and the PEC
enable option has been selected in the Menus > Service > Configuration > System menu.
The detector needs to know the length of the pack to enable it to function correctly.
Measure the product diagonally and enter that length to provide some tolerance and avoid the
generation of false triggers and nuisance error messages; for example where the external
packaging has curled up or packs are presented too close together. Then enter the pack
length in millimetres.
■ Reject delay
The following should be noted before setting up the Reject Delay and Reject Dwell timing for
a product.
93
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Manuais e produtos relacionados com Medição, teste e controlo RIDGID metal detector
(5 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais